x

ATM
Recycling-
systems GmbH

High quality and reliability over decades are the trademarks of our systems. ATM Recycling Systems has more than 80 years of experience in the processing of metallic residues. There are also a lot of references in the processing of production waste from the automotive and aircraft industries. High-quality metals such as titanium, magnesium, tungsten, molybdenum can be reused as secondary raw materials. A close cooperation with universities, research institutes, clusters, and ultimately with our customers enables us, to bring new technologies to the market and optimize our products.

Briquetting presses for metals

The briquetting systems are suitable for pressing chips from steel, cast iron, stainless steel, aluminium, magnesium, brass, copper, bronze, titanium, etc., also for special alloys, dusts and grinding sludges, as well as tire wires. Furthermore, it is possible to recover lubricating oils and coolants from grinding sludge and thus make a valuable ecological contribution. Highly compressed briquettes are better and safer to transport, store and require less energy in the production of new secondary raw materials.

Additional filling valve and servo controls reduce energy consumption by up to 40% and enable a performance-optimized compression of the materials. Energy consumption data and production data can also be managed and statistically exploited via our Internet portal. For maintenance and service planning, there is optionally a condition monitoring system and a remote maintenance portal.

Product

ArnoBrik – Briquetting presses for metals

Contact

ATM Recyclingsystems GmbH
Josef Ressel Gasse 8
8753 Fohnsdorf, AUSTRIA
Ph.: +43 (0)3573 27527 0
Fax: +43 (0)3573 27527 390
office@atm-recyclingsystems.com

Baler presses for metals

Balers are mainly placed in the automotive industry. They are used for pressing stamped scrap in the production of body or stamped parts. Another field of application is the scrap processing of bulky scrap in front of the melting process.
Due to the high production capacities of up to 50 tons / hour, mainly steel, aluminium and copper materials are pressed. The thus produced bales can be transported better and safer and require less energy during melting. Energy consumption data and production data can also be managed and statistically exploited via our Internet portal. For maintenance and service planning, there is optionally a condition monitoring system and a remote maintenance portal.

Product

ArnoPress – Baler presses for metals

Contact

ATM Recyclingsystems GmbH
Josef Ressel Gasse 8
8753 Fohnsdorf, AUSTRIA
Ph.: +43 (0)3573 27527 0
Fax: +43 (0)3573 27527 390
office@atm-recyclingsystems.com

Scrap shears

Die Schrottscheren dienen zum Zerkleinern von metallischen Abfällen vor dem Einschmelzprozess. Sie müssen verschiedenste Arten von Schrott wirtschaftlich verarbeiten können. Dafür ist im Scherenbett eine entsprechende Vorverdichtung notwendig. Ein Niederhalter fixiert dann das Material beim Schnitt, und der Hauptzylinder schert das Material mit einer Kraft von bis zu 13.000 KN entsprechend der getakteten Schnittlänge ab. Je nach Scherengröße können schwere Stahlkonstruktionen, Tanks oder Autokarossen geschnitten werden. Eine optionale Schienenbrechausrüstung ermöglicht die Verarbeitung von Eisenbahnschienen ohne Beanspruchung der Schermesser, da die Schienen gekerbt und gebrochen werden. Der Niederhalter dient auch zum Brechen von sperrigen Gussteilen. Mit den Zylindern des Vorverdichtungsbettes können auch Schrottpakete gepresst werden, womit die Schrottschere universell einsetzbar ist. Die Bedienung erfolgt wahlweise mit einer Fernbedienung vom Umschlagbagger aus oder über eine klimatisierte Steuerkabine mittels zweier Joysticks. Für Wartung und Serviceplanung gibt es optional ein Condition Monitoring System und ein Fernwartungsportal.

Product

ArnoCut – Scrap shears

Contact

ATM Recyclingsystems GmbH
Josef Ressel Gasse 8
8753 Fohnsdorf, AUSTRIA
Ph.: +43 (0)3573 27527 0
Fax: +43 (0)3573 27527 390
office@atm-recyclingsystems.com

Shredders

The shredders are available in different variations and capacities. 1, 2 or 4 shaft shredder for processing chips, stamping parts or loose materials, 1, 2 or 4 rotary shears for sheets and lumpy materials and with the heavy single shaft shredder, with up to 315 KW power, high throughputs of up to 10 tons be reached. An automatic rough parts flap enables the removal of non-shred able parts. If fine material is to be produced, a granulator can be used as second grinding stage, equipped with granulator knives. All systems are modularly configurable and are matched to your material with material-specific optimized cutting discs.

Product

ArnoShred – Shredders

Contact

ATM Recyclingsystems GmbH
Josef Ressel Gasse 8
8753 Fohnsdorf, AUSTRIA
Ph.: +43 (0)3573 27527 0
Fax: +43 (0)3573 27527 390
office@atm-recyclingsystems.com

Crushers for casting parts and railroad tracks

These crushers are used for efficient processing of gearboxes, engine blocks, molds and other cast scrap, or for crushing long used rails.
Due to the scissor-shaped movement of the serrated crushing arms, cast breakers produce a high break force for optimum part size for melting. The crushing process works against cutting processes with almost no tool wear.
Railway rails, however, are notched and then bent by a breaking cylinder.
Both processes are against usual cutting processes extremely low wear. The course of the breaking processes is optimized so that the energy requirement is minimal in comparison to other comminution processes.
As additional equipment, a remote control, air-conditioned cabin, loading crane, generator and conveyors can be offered.

Product

ArnoBreak – Cast iron breaker and rail breaker

Contact

ATM Recyclingsystems GmbH
Josef Ressel Gasse 8
8753 Fohnsdorf, AUSTRIA
Ph.: +43 (0)3573 27527 0
Fax: +43 (0)3573 27527 390
office@atm-recyclingsystems.com

Share this page: